上海振華迪拜5000T起重船ZPMC1142橡膠護舷、靠球技術規格書

jimosea

上海振華迪拜5000T起重船ZPMC1142橡膠

護舷

、

靠球

技術規格書

充氣橡膠護舷 Pneumatic Rubber Fender
2.1 產品規格 Products Requirements：
名稱：充氣橡膠護舷:Φ2500mm×L5500mm
Name: Pneumatic Rubber Fender:Φ2500mm×L5500mm
類型：50 型Ⅱ型（懸掛式）
TYPE: 50- Type II (suspension type)
執行標準：GB/T 21482-2019
Standard: GB/T 21482-2019
數量：4 套
QTY.：4 sets
2.2 使用環境條件 Environmental Conditions
1）使用介質：海水；
Use medium：seawater
2）環境溫度：16℃＋55℃
Environmental temperature: 16℃＋55℃
3）工作條件：充氣橡膠護舷在海水中滿足船舶靠泊作業使用。
Working requirement: pneumatic rubber fender following barge mooring working in seawater.
2.3 技術要求 Technical Requirement
1) 充氣橡膠護舷主體材料為橡膠，骨架層為掛膠簾線，內外層橡膠要保證在使用期限內保
持足夠的硬度，耐刺，耐酸堿，耐臭氧老化；
Main material is rubber, the skeleton layer is cord ply, the inside-outside glue layer need to be
confirmed which will keep enough hardness, stab-resistance, acid and alkali resistant and Ozone
aging resistance in service life.
2) 充氣橡膠護舷所用材料的物理性能、主要成分、力學性能指標等要達到本規格書要求（見
表 1）和 GB/T 21482-2019 標準要求；
The physical performance, main material ,force performance and other index of module
pneumatic rubber fender’s material need to meet the this document(see the table 1) and GB/T
21482-2019 standard requirements.
3) 充氣橡膠護舷材料需耐海水腐蝕；
The pneumatic rubber fender material needs to be seawater corrosion resistance.
4) 充氣橡膠護舷的兩端 Q235 熱鍍鋅吊環和卸扣強度需達到技術要求，滿足吊運懸掛使用；
The strength of Q235 HDG lifting rings and shackles at both sides of pneumatic rubber fender
are should be meet the technical requirements and could satisfy the handling.
5) 球體外觀要求光滑、平整，可以有模具縫，但不能有氣泡和橡膠片搭接；
The surface of the sphere should be flush and flat which could have mould gap but can’t havebubble and rubbers joint.
6) 球體內外法蘭和螺栓需使用 SUS316L 材質，防海水腐蝕；
The flange of sphere inside and outside bolts need to be SUS316L to avoid seawater corrosion.
7) 球體需高溫高壓硫化，內層膠、簾線層和外層膠三個結構層之間不得有任何脫層和間隙；
Sphere should be vulcanized in high temperature and high pressure condition,and the three
different layer, inside glue, cord ply and outside glue, can’t have any delaminating or gap.
8) 球體兩端需有帶有規格型號，出廠日期、出廠編號、工作壓力等標識，標識為永久性；
On both side of sphere need to add forever marking which include type, date of production,
factory number, working pressure and other marking.
9) 充氣橡膠護舷被壓縮變形 60%時反力和吸能應滿足性能要求；
When the module pneumatic rubber fender is stressed 60% transformation, the reinforce and
energy absorption should meet the performance requirements.
10) 安全閥壓力上限 175Kpa，球體內壓力超過 175Kpa 時安全閥必須自動開啟泄壓。初充氣
壓力 50Kpa,安全閥設定壓力 175Kpa；排氣壓力在 175Kpa 時，安全閥流量為 750 立方米
/h；
The upper limit pressure for safety valve is 175Kpa, and the valve will auto release pressure
when the inside pressure of sphere exceed 175Kpa. The pressure is 50Kpa at first filling, and the
safety valve set pressure at 175Kpa. When venting pressure is 175Kpa, the flow valve is 750
stere per hour.



輪胎護舷 Tire Fender
4.1 產品規格 Product Specification：
執行標準：GB/T 2980-2018
Standard: GB/T 2980-2018
輪胎護舷直徑：φ1615mm，斷面寬度：595mm，數量：16 套。
Tire Fender diameter: φ1615mm, Section Width: about 595mm，QTY.： 16 sets.
4.2 技術要求 Technical Requirements：
1) 輪胎護舷樣式見下圖；
The detail of tire fender see the following drawing；






D 型護舷 D-shape rubber Fender
3.1 產品規格 Product Specification：
D 橡膠護舷：400x400xL：~7.1 米（8 條）、~5.8 米（2 條）、6.8 米（2 條）
D-Shape rubber Fender: 400x400xL：~7.1m（8 sets）、~5.8m（2 sets）、6.8m（2 sets）
執行標準：HG/T 2866-2016
Standard: HG/T 2866-2016
3.2 技術要求 Technical Requirements：
壓縮 Stress
型號 Type
設計壓縮變形 40%
Design Compression Deformation 40%
反力 Reaction
KN/M
吸能量 Energy
Absorption
KN-M/M
D 型 400H
D-Shape 400H
≤202
≥14.5
1) 性能公差±10%；
The tolerance of performance:±10%；
2) 數值為每米數值；
The number of table is per meter；
3) 按圖提供所有 D 型護舷的 SS316L 緊固件；
All SS316L fasteners of D-shape rubber fender should be provided according to the DWG;
4) D 型護舷需廠家預彎出廠；
D-shape fenders need to be pre-bended before supply.